Nissan Primera

1990-1992 of release

Repair and car operation

Nissan Primera
+ Nissan Primera brand Cars
- Current leaving and service
   - Schedule of routine maintenance
      Current leaving
      General information on control
      Check of levels of liquids
      Check of a condition of tires and pressure in them
      Replacement of impellent oil and oil filter
      Check of level of liquid of system of hydrostrengthening of a wheel
      Check of level of liquid of automatic transmission
      Rotation of wheels
      Check of a condition and replacement of hoses of an impellent compartment
      Condition check, adjustment of a tension and replacement of driving belts
      Check and adjustment of turns of idling of the engine and level WITH
      Check of a condition of the battery, care of it and charging
      Check and replacement of spark plugs
      Check and replacement of candle VV of wires, covers and distributor begunka
      Check of level of oil in a manual box of gear shifting
      Check and adjustment of gaps of valves
      Check and greasing of draft of a drive of a butterfly valve
      Replacement of an element of the air filter
      Check of fuel system
      Check of functioning of system of cooling
      Check of a condition of system of production of the fulfilled gases
      Check of a condition of components of a suspension bracket and steering
      Check of a condition of protective covers of power shafts
      Check of brake system
      Check of a condition and replacement of brushes of screen wipers
      Replacement of transmission liquid
      Plums, washing and filling of system of cooling
      Replacement of the fuel filter
      Replacement of transmission oil of manual transmission
+ Engine
+ cooling and heating Systems
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Manual transmission, differential and main transfer
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Appendices


Check and replacement of candle VV of wires, covers and distributor begunka

Annually or each 20000 km of run

Check of a condition of candle VV of wires should be made regularly through the recommended intervals and each time at replacement of spark plugs.


  1. Begin this procedure with external survey of wires at the working engine. In the blacked-out garage (track that indoors there was a good ventilation) start the engine and attentively examine each wire. Try not to touch moving parts of the engine. In the presence of break the wire will spark in a damage place. In this case replace wires, then let's to the engine cool down.
  2. Disconnect a negative wire of the battery.

If the radio receiver of your car is equipped with system of protection against theft, make sure that you gathered the correct code before a battery detachment.

  1. In order to avoid confusion at installation check of VV of wires should be made serially.
  2. Disconnect VV a wire from a spark plug. Do not pull for a wire, only and I will corrode.
  3. Examine an internal part of the socket on existence of corrosion which looks like a white friable powder. Connect a wire with the socket to a spark plug. The socket should hardly a network on a candle. If it is not possible to reach it, again remove a wire and correct flat-nose pliers position of the plug in the socket.
  4. Pure rags wipe wires outside on all length, deleting from them the stuck dirt and greasing. After cleaning check a wire on existence of traces прогаров, cracks and other damages. Do not bend a wire under acute angles since it can lead to a conductor fiasco.
  5. Disconnect VV a wire from the distributor. Do not forget to pull only for the socket. Check it on existence of corrosion and connect in the same way, as well as a spark plug wire. If necessary replace a distributor wire.
  6. Check other wires of spark plugs, and after check make sure that each of them is reliably attached to the distributor and a candle.
  7. If candle wires demand replacement, buy the set of the wires which has been specially intended for your model of the engine. Wires of the necessary length enter into sets and with the established sockets. Remove and replace wire VV on one not to allow confusion in an operating procedure of cylinders at their installation.
  8. Weaken screws or open clips, then uncover the distributor. Give screws (if they are available) and remove a begunok from a shaft. Check a cover and a distributor begunok on existence of signs of wear, cracks, coal traces and the worn-out, burned slightly or weakened contacts. At detection of defects replace a cover or a begunok. Usually a cover and a begunok it is accepted to replace each time at replacement of candle wires. At installation of a new cover on one disconnect wire VV from an old cover and connect them to new in just the same order - never disconnect all wires at the same time in order to avoid confusion in an operating procedure of cylinders at their installation.
  1. Take away a distributor cover so that it was possible to examine it from within.
  1. Remove a begunok from a shaft.

In drawing covers of the distributor some of widespread defects to which it is necessary to pay attention at survey (if there are doubts concerning its condition, replace it better) are shown.